- On sale!
- -42%
- New
Toshiba TEC B-FP3D Mobile Thermal Printhead 203 DPI FMBC0137701
- Write a review
$195.00
$113.10
Save 42%
Authentic OEM 203 DPI thermal printhead module for Toshiba TEC B-FP3D rugged 3-inch mobile receipt and label printers. Delivers clean direct thermal output for route accounting, warehouse mobility, and field ticketing. Factory-certified replacement.
OEM Replacement Component
Toshiba TEC B-FP3D Series 3-Inch Mobile Thermal Printhead (203 DPI)
OEM Part Number: FMBC0137701 | Genuine Next-Generation Mid-Format Portable Direct Thermal Line Head Assembly
Product Overview
The Toshiba TEC FMBC0137701 is an authentic original equipment manufacturer (OEM) replacement thermal printhead engineered specifically for the Toshiba TEC B-FP3D 3-inch mobile printer series. Built for high-tempo direct store delivery (DSD), logistics receipt printing, route distribution, mobile traffic citation, and on-demand warehouse barcode labeling, this line head delivers crisp 203 DPI (8.0 dots/mm) resolution across an active 2.83-inch (72.0 mm) continuous printline width.
Constructed with an advanced energy-efficient thin-film ceramic resistive array of 576 heating elements, the FMBC0137701 maximizes battery longevity while maintaining dense optical blackness across broad outdoor ambient temperature ranges. It features an anti-wear dielectric glass glaze formulated to resist abrasive direct thermal receipt papers and sticky residues from linerless label stocks. Pre-engineered pivot alignment tabs and an integrated lightweight aluminum heatsink ensure direct drop-in replacement into the B-FP3D ruggedized clamshell carriage, restoring factory-original barcode integrity and high-speed print capability up to 6 inches per second.
Part Information
| Product Name | Toshiba TEC B-FP3D Mobile Thermal Printhead |
| OEM Manufacturer | Toshiba TEC Corporation |
| OEM Part Number | FMBC0137701 |
| Component Classification | Original Equipment Manufacturer (OEM) Replacement Thermal Printhead |
| Chassis & Architecture | Thin-Film Glazed Ceramic Linear Matrix on Form-Fitted Aluminum Heatsink Base |
| Manufacturing Standard | Toshiba TEC Factory Certified (Japan) |
Technical Specifications
| Printing Technology | Direct Thermal (DT) Dedicated |
| Native Resolution | 203 DPI (8.0 dots/mm) |
| Dot Pitch | 0.125 mm (nominal dot-to-dot spacing) |
| Effective Print Width | Up to 72.0 mm (2.83 inches / 3-inch nominal format) |
| Total Heating Elements | 576 Dots (continuous linear array) |
| Rated Print Speed | Up to 6.0 ips (152.4 mm/sec) — battery charge and media thermal sensitivity dependent |
| Media Compatibility | Direct thermal receipt papers, continuous rolls, die-cut label stocks, and linerless media |
| Electrical Interface | Flexible Printed Circuit (FPC) tail with zero-insertion-force (ZIF) termination |
| Thermal Management | Integrated internal thermistor providing closed-loop strobe pulse modulation for battery optimization |
Key Features & Operational Advantages
- Full 72 mm Mid-Format Coverage: 576-dot array provides expansive 3-inch receipt and label printing, perfectly formatted for wider route delivery invoices and warehouse bin labels without side-margin compression.
- High-Efficiency Battery Profile: Low-voltage resistive elements fire with high thermal conversion efficiency, conserving portable lithium-ion battery reserves during long field shifts.
- Linerless & Chemical Topcoat Resistance: Hardened dielectric glass surface layer minimizes adhesive buildup, prevents electrostatic breakdown, and resists abrasive scoring from continuous direct thermal media contact.
- Drop-In Factory Calibration: Pre-ranked factory resistance ratings align directly with B-FP3D mainboard firmware, eliminating manual voltage adjustments and ensuring balanced current distribution.
CRITICAL TECHNICAL & OPERATIONAL ADVISORY
1. Mandatory ESD Precautions: Microscopic thin-film heater elements and onboard driver shift registers are Class 1 ESD-sensitive components. Technicians must wear a grounded ESD wrist strap and work on a static-dissipative work surface. Never touch the ceramic dot array or signal connector terminals directly.
2. Complete Power Isolation: Always power off the mobile printer and physically remove the rechargeable battery pack before replacing the printhead. Disconnecting or seating the flexible circuit harness while the logic board is energized will cause instantaneous gate blowout in the driver ICs and permanently destroy the head.
3. FPC Cable Terminal Care: Mobile flexible printed circuits have thin polyimide substrates. Do not sharply crease, bend, or pull the flexible connector tail during installation. Ensure the ZIF locking clip on the main PCB is unlocked before inserting the cable squarely.
4. Preventive Cleaning Regimen: Direct thermal stocks generate high paper-dust and chemical residue. Clean the dot line regularly using a lint-free swab moistened with 99.7% electronic-grade Isopropyl Alcohol (IPA). Allow the solvent to dry completely before latching the clamshell cover. Never use metal blades or abrasive pads to remove debris.
Compatible Models & Systems
| System Family | Native Resolution | Supported Models |
|---|---|---|
| Toshiba TEC B-FP3D Series | 203 DPI (8.0 dots/mm) | B-FP3D-GS30-QM-R / B-FP3D-GS40-QM-R |
| Toshiba TEC B-FP3D Linerless | 203 DPI (8.0 dots/mm) | B-FP3D Mobile 3-inch Line (Standard & Linerless Models) |
*Model Differentiation Note: This printhead is dedicated strictly to the 3-inch B-FP3D series. It is NOT physically or electrically compatible with the narrower 2-inch B-FP2D mobile units (Part # FMBC0147601) nor older B-EP series models. Always verify the printer model code on the base rating plate prior to unsealing the component.
Terms, Warranty & Customer Protection
Condition: 100% Brand New, Unopened Factory Original Genuine OEM Component in Factory-Sealed Anti-Static Packaging.
Warranty Scope: Covered by standard manufacturer DOA replacement protection against electrical continuity failures and physical manufacturing defects upon initial arrival. Operating longevity depends entirely on media abrasiveness, environmental exposure, operating heat levels, and adherence to routine cleaning schedules.
Return Policy: Precision industrial electronic consumable. Due to sensitivity to electrostatic discharge and inherent operational wear characteristics, components that have been unsealed from their protective static-shielding bag, mounted, or energized on a printer cannot be returned or restocked under standard commercial terms. Please confirm your printer model and OEM part number with technical support prior to unsealing.
FMBC0137701
190 Items
